BWHMK - 6400 SEMI-GLOSS HIGH SOLID POLYURETHANE
- MSDS: BWHMK
- Manufacturer: CARDINAL INDUSTRIAL FINISHES
- Product Name: 6400 SEMI-GLOSS HIGH SOLID POLYURETHANE
- National Stock Number: 8010-00F016387
Product Identification
Product ID:6400 SEMI-GLOSS HIGH SOLID POLYURETHANE
MSDS Date:06/30/1994
FSC:8010
NIIN:00F016387
MSDS Number: BWHMK
Responsible Party
SOUTH EL MONTE, CA 91733-3012
US
Emergency Phone: 818-444-9274/213-283-9335
Info Phone: 818-444-9274/213-283-9335
Preparer: BOB SYPOWICZ
Cage: 65860
Contractor
Telephone: 818-444-9274 OR 213-283-9335
Cage: 65860
Ingredients
2-BUTANONE (METHYL ETHYL KETONE) (MEK)
CAS: 78-93-3
RTECS: EL6475000
Fraction By Weight: 3%
OSHA PEL 200 PPM
ACGIH TLV: 300 PPM
EPA Report Quantity: 5000 LBS
DOT Report Quantity: 5000 LBS
2-HEPTANONE, METHYL N-AMYL KETONE
CAS: 110-43-0
RTECS: MJ5075000
Fraction By Weight: 9%
OSHA PEL 100 PPM
ACGIH TLV: 50 PPM
BUTYL ACETATE (N-BUTYL ACETATE) *94-4*
CAS: 123-86-4
RTECS: AF7350000
Fraction By Weight: 10%
OSHA PEL 150 PPM
ACGIH TLV: 200 PPM
EPA Report Quantity: 5000 LBS
DOT Report Quantity: 5000 LBS
EXCLUDING/INCLUDING WATER 337
RTECS: 9999999VO
Hazards
Routes of Entry: Inhalation:YES Skin:YES Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:EYES: CAN CAUSE IRRITATION. SKIN:
MODERATE IRRITATION, DERMATITIS. INHALATION: NASAL IRRITATION.
INGESTION: GI IRRITATION. PAINT & SOLVENTS HAVE BEEN LINKED TO
LIVER ABNORMALITIES, KIDNEY & LUNG DAMAG E.
Explanation of Carcinogenicity:NONE
Effects of Overexposure:IRRITATION, REDNESS, TEARING, BLURRED VISION,
HEADACHE, DIZZINESS, NAUSEA, WEAKNESS, VOMITING, LOSS OF
CONSCIOUSNESS.
Medical Cond Aggravated by Exposure:PRE-EXISTING RESPIRATORY
CONDITIONS, SKIN DISORDERS, LIVER & KIDNEY DISORDERS.
First Aid
First Aid:EYES: FLUSH W/WATER FOR 15 MINS. SKIN: WASH EXPOSED AREA
W/SOAP & WATER. INHALATION: REMOVE TO FRESH AIR. GIVE OXYGEN/CPR,
IF NEEDED. INGESTION: DON'T INDUCE VOMITING. KEEP WARM & QUIET.
OBTAIN MEDICA L ATTENTION IN ALL CASES.
Fire Fighting
Flash Point Method:TCC
Flash Point:24F
Lower Limits:1.1
Upper Limits:11.4
Extinguishing Media:FOAM, DRY CHEMICAL, CO2, WATER FOG.
Fire Fighting Procedures:WEAR SCBA W/FULL FACE PIECE OPERATED IN A
PRESSURE DEMAND/OTHER POSITIVE PRESSURE MODE.
Unusual Fire/Explosion Hazard:CONTAINERS MAY DEFORM/EXPOLDE WHEN EXPOSE
TO EXTREME HEAT.
Accidental Release
Spill Release Procedures:ELIMINATE ALL IGNITION SOURCES, ABSORB LIQUID
IN ABSORBENT MATERIAL & PREVENT SPREADING TO GROUND WATER.
Handling
Handling and Storage Precautions:CONTAINERS OF THIS MATERIAL MAY BE
HAZARDOUS WHEN EMPTIED. EMPTY CONTAINERS RETAIN PRODUCT RESIDUALS,
VAPOR, LIQUID &/SOLID.
Other Precautions:THIS COATING IS A WATERBORNE OF LOW TOXICITY.
Exposure Controls
Respiratory Protection:IF TLV OF THE PRODUCT/ANY COMPONENT IS EXCEEDED,
A NIOSH/MSHA JOINTLY APPROVED AIR SUPPLIED RESPIRATOR IS ADVISED.
IN LIEU OF AIR MONITORING DATA, AIR SUPPLIED RESPIRATORS ARE
SUGGESTED FOR SPRAY APPL ICATION.
Ventilation:PROVIDE SUFFICIENT MECHANICAL (GENERAL &/LOCAL EXHAUST) TO
MAINTAIN EXPOSURE < TLV.
Protective Gloves:IMPERVIOUS
Eye Protection:CHEMICAL SPLASH GOGGLES
Other Protective Equipment:GB PROTECTIVE HAND CREAM, IMPERVIOUS
CLOTHING & CHEMICAL RESISTANT BOOTS.
Work Hygienic Practices:REMOVE/LAUNDER CONTAMINATED CLOTHING BEFORE
REUSE. WASH HANDS BEFORE EATING/USING RESTROOM. SMOKE IN SMOKING
AREAS ONLY.
Supplemental Safety and Health
Chemical Properties
Boiling Pt:B.P. Text:175-304F
Vapor Density:>1
Evaporation Rate & Reference:SLOWER THAN ETHER
Percent Volatiles by Volume:38-40
Stability
Stability Indicator/Materials to Avoid:YES
ALKALIS, STRONG OXIDIZING AGENTS.
Stability Condition to Avoid:EXTREME TEMPS.
Hazardous Decomposition Products:OXIDES OF CARBON & NITROGEN.
Conditions to Avoid Polymerization:WHEN MIXED W/CATALYST, PRODUCT WILL
REACT W/WATER, ALCOHOLS & AMINES.
Disposal
Waste Disposal Methods:CONTAMINATED ABSORBENT SHOULD BE
INCINERATED/SENT TO APPROVED LANDFILL IAW/FEDERAL, STATE & LOCAL
REGULATIONS. FLAMMABLE UN1263.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.